有时候我们会碰到忘记Netscaler的密码，或接手别人的设备而不知道密码的情况。在这种情况下能看到但进不去，那感觉真是酸爽！如何初始化Netscaler的密码，及时启用手上的设备就很重要了。

成都创新互联公司长期为千余家客户提供的网站建设服务，团队从业经验10年，关注不同地域、不同群体，并针对不同对象提供差异化的产品和服务；打造开放共赢平台，与合作伙伴共同营造健康的互联网生态环境。为咸丰企业提供专业的成都网站制作、网站建设，咸丰网站改版等技术服务。拥有10余年丰富建站经验和众多成功案例,为您定制开发。

用console线连接到Netscaler，按启动按钮后会看到以下内容，按照如下提示操作即可

1.       Attach a console cable to the Serial Console (9600 baud, 8 bits, 1 stop bit, No parity) of the NetScaler appliance.

 

2.       Restart the NetScaler appliance.

 

3.       Press any of the following keys, as prompted:

Press Spacebar when the following message is displayed:

 

Hit [Enter] to boot immediately, or any other key for command prompt Booting [kernel] in 10 seconds

Press Ctrl and C keys simultaneously when the following message is displayed:

Press [Ctrl-C] for command prompt, or any other key to boot immediately.

Booting [kernel] in 2 seconds...

 

4.       To start the appliance kernel on a single user mode, enter the following command:

 

boot –s

 

Note: If boot -s does not work, then try reboot -- -s and appliance will reboot in single user mode.

 

5.       Press Enter when the following message is displayed:

 

Enter full pathname of shell or RETURN for /bin/sh:

 

Note: Notice that the prompt of the appliance changes to \u@\h\$.

 

6.       Run the following command to check the disk consistency:

 

\u@\h\$ /sbin/fsck /dev/ad0s1a（此命令一定要先执行，否则不能挂载/flash）

 

Note: Refer to the Knowledge Center article CTX121853 – Device Names Assigned to Hard Disk in Various Models of the Citrix NetScaler Appliance to verify the device name assigned to the hard disk of the appliance model and replace ad0s1a in the preceding command with the appropriate device name.

 

7.       Run the following command to display the mounted partitions:

 

df

 

8.       Run the following command to mount the flash drive:

 

\u@\h\$ /sbin/mount /dev/ad0s1a /flash( 一定要把flash挂上，否则看不到ns.conf）

 

If the preceding command fails to mount the flash drive, then run the following command to create the flash directory and then run the preceding command again to mount the drive:

 

\u@\h\$ mkdir /flash（如果有/flash可以不执行这步）

 

9.       Run the following command to change to the nsconfig directory:

 

\u@\h\$ cd /flash/nsconfig

 

10.     Run the following set of commands to rewrite the ns.conf file and remove the set of system commands defaulting to the nsroot user:

a. Run the following command to create a new configuration file that does not have commands defaulting to the nsroot user:

\u@\h\$ grep –v “set system user nsroot” ns.conf > new.conf（提取除nsroot用户以外的其他配置到新文件）

b. Run a command similar to the following command to make a backup of the existing configuration file:

\u@\h\$ mv ns.conf old.ns.conf（备份原来的配置）

c. Run the following command to rename the new.conf file to ns.conf:

\u@\h\$ mv new.conf ns.conf（用没有nsroot的配置启动）

 

11.     Run the following command to restart the appliance:

 

reboot

 

12.     Log in to the appliance by using the default nsroot user credentials.

此时nsroot的密码为初始化的密码，直接输入nsroot登陆即可

13.     Run the following command to reset the nsroot user password of your choice:

 

> set system user nsroot重新输入密码

当前题目：Netscaler重置密码的方法
文章路径：http://hbruida.cn/article/jdhpgc.html